tesa.com에 대한 쿠키 설정
당사는 쿠키 및 기타 기술(타사 서비스 포함)을 사용하여 웹 사이트 기능을 제공하며, 사용량을 이해하고, 제품을 최적화하며 개별화된 서비스 제품 및 광고를 제공합니다. 더 자세한 내용은 언제든지 쿠키 설정을 변경할 수 있는 당사의 개인정보처리방침 및 당사의 쿠키정책을 확인하세요.
200μm x-linkable polyurethane black HAF mounting tape
제품 기능
Extremely high bonding performance and reliability, even on thin design gaps
Excellent shock resistance
Extremely low oozing ratio
모든 제품 기능Product description
200μm x-linkable polyurethane black HAF
mounting tape
Long description tesa ® XPU 58708 is a reactive mounting
tape offering high bonding strength and elasticity after curing. This black
double-sided tape has no backing. It is protected by a PE-coated paper liner.
It is activated by heat and pressure applied during the assembly
process.
Special features:
Black design
제품 세부 사항 및 사양
제품 기능
Extremely high bonding performance and reliability, even on thin design gaps
Excellent shock resistance
Extremely low oozing ratio
tesa ® XPU 58708 is free of halogen according to IEC 61249-2-21 and compliant with current RoHS directive.
At room temperature tesa ® XPU 58708 is not tacky.
Application Fields
tesa ® XPU 58708 is especially recommended for structural bonding of various substrates inside electronic devices:
• Bonding of plastics
• Bonding of metals
• Bonding of electronic components
Product Construction
Type of adhesive
type: crosslinkable polyurethane
Type of liner
type: PE-coated paper
기재 소재
없음
총두께
200 µm
컬러
검정
Product Construction
Type of adhesive
type: crosslinkable polyurethane
Type of liner
type: PE-coated paper
기재 소재
없음
총두께
200 µm
컬러
검정
Properties / Performance Values
점착력 (푸쉬 아웃)
4 N/mm²
Properties / Performance Values
점착력 (푸쉬 아웃)
4 N/mm²
Additional Info
Technical recommendations: tesa® XPU 58708 is not self-adhesive. It is
activated by heat and pressure over a certain interval. The following values
are recommendations for bond line parameters to start with.
• Pre-lamination
During pre-lamination, laminate the
adhesive tape onto the first component.
Setting:
Temperature¹ 55-65 °C
Pressure² 3 bar
Time 5 – 20 s
Short-time exposure to 65 °C bond line
temperature during pre-lamination does not affect the final bonding potential.
2. Bonding
Remove the liner from tape after the
pre-lamination step.Position the second component.
Apply temperature and pressure for the
bonding time to reach sufficient bonding strength.
2.1. PC/PC:Setting:
• Temperature¹ 80 – 140 °C
• Pressure² 5 bar
• Time 10 – 120 s
2.2. AL/PC:Setting:
• Temperature¹ 110 – 190 °C
• Pressure² 5 bar
• Time 20 – 120 s
Short cycle times can be achieved at high
bond line temperatures. For activation at low temperatures, increase the heat-press
time. To reach maximum bonding strength, surfaces should be clean and dry.
Allow at least 1-2 hours dwell-time after bonding before performance testing.
Final bonding strength will be reached after 24 hours. Bonding strength values
were obtained under standard laboratory conditions. PC/PC: bonding conditions:
temperature = 110 °C
(120 °C jig); pressure = 5 bar; time = 60
sec Storage: tesa® recommends storage in original packaging in cool and dry conditions.
• ‘Pre-lamination’ and ‘Bonding’
temperature refer to the data that is measured in the bond line.
tesa® products prove their impressive quality day in, day out in demanding conditions and are regularly subjected to strict controls. All technical information and data above mentioned are provided to the best of our knowledge on the basis of our practical experience. They shall be considered as average values and are not appropriate for a specification. Therefore tesa SE can make no warranties, expressed or implied, including, but not limited to any implied warranty of merchantability or fitness for a particular purpose. The user is responsible for determining whether the tesa® product is fit for a particular purpose and suitable for the user’s method of application. If you are in any doubt, our technical staff will be glad to support you.