tesa_60155_front_001_pr

tesa® 60155 Adhesion Promoter EcoBond

Surface treatment to improve adhesion to various substrates

  • It enhances better and faster adhesion of tesa's ACX product family on various substrates.
  • It is a special adhesion-promoting solution for the pretreatment of surfaces prior to bonding.

Product description

tesa® 60155 Adhesion Promoter EcoBond is a fast-acting, transparent, isopropanol-based adhesion promoter especially designed for an improved impact on the environment and work conditions.

Application Fields

We recommend using our tesa® 60155 Adhesion Promoter EcoBond to improve the adhesion on several substrates, particularly on most metals (e.g., aluminum and steel) and other non-porous materials. It is not suitable, however, for plastics and other low-surface-energy substrates. The compatibility with other surfaces/substrates should always be tested accordingly. This product can be used to improve the bonding strength of tesa® ACXplus tapes as testing shows significantly higher peel adhesion values.
Product Advantages: tesa® 60155 Adhesion Promoter EcoBond offers the following benefits:
  • Eco-friendlier1
  • Reduced hazard to health1
  • Non-offensive odor1
  • Enhanced tape adhesion on various substrates
  • Improved working conditions

1 Compared to existing tesa® adhesion promoter assortment

Product Construction

Color transparent

Properties / Performance Values

Consistency liquid
Spreading rate ca. 15 m²/l
Solids 3 %
Density 0.8 g/cm³
Viscosity 2 mPa s

Additional Info

Before using our adhesion promoter, the bonding surface should be free of dust, grease, oil, moisture, and other contaminants. Therefore, we highly recommend cleaning the substrate with a lint-free cloth using solvents, such as ethanol, isopropanol or our tesa® 60040 Industry Cleaner. Once the surface has been cleaned, you can go ahead and apply our tesa® 60155 Adhesion Promoter EcoBond. The ideal application and surface temperature is between 15 °C and 25 °C. For exterior applications, please always involve your local sales representative or directly contact our customer solution center (CSC).
We recommend applying our adhesion promoter with a lint-free cloth (pen, brush or sponge should not be used). Wipe only once and in one direction (Do not go back and forth). The entire surface should be coated thinly with the adhesion promoter in order to reach the highest bonding performance. Excess of activator could lead to adhesion failure. It is important to wait at least 10 minutes in order to give solvents time to evaporate. Please make sure to keep the prepared surface free of contaminants prior to applying the tape.
Once the substrate has been pre-treated properly with tesa® 60155 Adhesion Promoter EcoBond, the bond should be established within 2 hours. If the pre-treated area is not bonded within 2 hours, the activation process has to be repeated (once only). Please note that due to the multitude of available substrate formulations in the marketplace, we recommend testing our tesa® 60155 Adhesion Promoter EcoBond prior to usage.
Tightly reseal container immediately after each use. tesa® 60155 Adhesion Promoter EcoBond is a moisture reactive system. Prolonged exposure to atmospheric moisture will cause the product to become turbid and thus inactive. Do not use tesa® 60155 Adhesion Promoter EcoBond if it has become opaque instead of transparent. If used on transparent or translucent substrates such as float glass, plastics, etc., an adequate UV protection is mandatory.
The shelf life of this product amounts to at least 12 months when stored at room temperature in its original sealed container. For further information and advice on safe handling, please refer to our safety data sheet (SDS), which is available upon request.
tesa® products prove their impressive quality day in, day out in demanding conditions and are regularly subjected to strict controls. All technical information and data above mentioned are provided to the best of our knowledge on the basis of our practical experience. They shall be considered as average values and are not appropriate for a specification. Therefore tesa SE can make no warranties, expressed or implied, including, but not limited to any implied warranty of merchantability or fitness for a particular purpose. The user is responsible for determining whether the tesa® product is fit for a particular purpose and suitable for the user’s method of application. If you are in any doubt, our technical staff will be glad to support you.

Related products